Cart Preview
FMS067(SD)

FMS 1400mm F3A Olympus pattern plane - Receiver Ready - FMS067

Scratch and Dent Details:
  • Product condition: Customer Return
  • Missing parts: None
  • Damage/defects: Wings have a 'hard stop' plug in them for the wing tube - this is glued in the wrong place so the wings do not slide into the tube as far as they should. Wing spars only slide in about 8" instead of 11". Also, The fuse is warped so the tail is twisted.
Please Note: Because of their deeply discounted prices, scratch and dent items cannot be returned or exchanged even if more is discovered to be found wrong beyond what was reported.

 

FMS F3A Build Review and First Impressions

The build quality is outstanding. Minimal glue was required to build this plane and everything screwed together with ease. The servos are all 17g digital metal gear for precision and durability. The ducting is sufficient for maximum airflow to cool the electronics. Building was pretty much a non-event. The wing and elevator are two pieces and go together quickly without hassle. The main wing uses two tubular carbon fiber spars, and their plastic mounting shrouds are well aligned. The main wing needed zero adjustment, while the elevator's port spar mounting shroud was 2 degrees off 180. Compressing the foam at the junction point was enough to seat the elevator back to flush. We completed the task in a little over an hour.

FMS F3A Flight Review

We flew the F3A using a 6S 4000mAh LiPo pack and we also flew it using a 5S 4000mAh LiPo pack. We felt the 5S was a little better for 3D while the 6S was good for sport flying. We found knife edges were very stable and the control surfaces are large enough to hold F3A patterns. We were able to do snap rolls and everything you would expect from an F3A pattern plane using either battery. Flight duration was between 6 and 8 min depending on how much throttle we were using. Power from the 2 blade prop was adequate. We recommend removing the Y cables for ailerons which will allow you to subtrim the individual aileron servos to perfection.

Features:

  • Fully hinged rudder using Dubro style hinges (superior to foam hinges)
  • 17g digital metal gear servos
  • High performance 550kV PAEP motor
  • 70 Amp ESC
  • 2 blade 15 x 8 prop for enhanced performance
  • Carbon spars and EPO foam construction provide the perfect balance between strength and flexibility
  • Outrunner motor, servos, and ESC come pre-installed for your convenience

Requires:

  • Minimum 4 Channel Radio - Click Here for recommendations
  • 4 Channel Receiver - Click Here for recommendations
  • 6 Cell 22.2V 4000 mAh LiPo Battery - Click Here or 5S 18.5V 4000mAh LiPo battery - Click Here
  • Lipo Battery Charger - Click Here for recommendations
Skill Level: IntermediateArrow.jpgBuild Time: 2 HoursAge Level: 14 and upArrow_End.jpg

canada-flat-icon.png Canadian Customers: This product is too large to ship via US Postal Service. You MUST select UPS for shipping method during checkout.

FEATURE VIDEO: FMS 1400mm F3A Olympus Pattern Plane Demo Flight by Motion RC

Wingspan

1400mm / 55.1in

Length

1548mm / 61in

Flying Weight

2400g / 5.3lb

CG (Center of Gravity) 150mm to 160mm from leading edge

Power System

4258-550kV Brushless Outrunner Motor

Electronic Speed Control

70A ESC, 5A SBEC, T Connector

Propeller / EDF

15x8 2 Blade

Servos

17g digital metal gear for, rudder
2x 17g digital metal gear, left and right ailerons
2x 17g digital metal gear, left and right elevator

Landing Gear fixed landing gear - 4mm wire

Required Battery

6S 22.2V 3300-4000mAh 35C LiPo or 5S 18.5V 3300-4000mAh 35C LiPo

Required Radio

4 Channel, 6 channel recommended

Ailerons Yes

Elevator

Yes

Rudder Yes

Flaps

No

Lights

No

Hinge Type

Nylon hinges

Material EPO Foam
Skill Level Advanced Intermediate
Build Time 2 Hours
Recommended Environment Outdoor
/fms-1400-f3a/

Product Specifications:

AGE LEVEL : 14 and up
SKILL LEVEL : Intermediate
BUILD TIME : 2 Hours

Wingspan

1400mm / 55.1in

Length

1548mm / 61in

Flying Weight

2400g / 5.3lb

CG (Center of Gravity)150mm to 160mm from leading edge

Power System

4258-550kV Brushless Outrunner Motor

Electronic Speed Control

70A ESC, 5A SBEC, T Connector

Propeller / EDF

15x8 2 Blade

Servos

17g digital metal gear for, rudder
2x 17g digital metal gear, left and right ailerons
2x 17g digital metal gear, left and right elevator

Landing Gearfixed landing gear - 4mm wire

Required Battery

6S 22.2V 3300-4000mAh 35C LiPo or 5S 18.5V 3300-4000mAh 35C LiPo

Required Radio

4 Channel, 6 channel recommended

AileronsYes

Elevator

Yes

RudderYes

Flaps

No

Lights

No

Hinge Type

Nylon hinges

MaterialEPO Foam
Skill LevelAdvanced Intermediate
Build Time2 Hours
Recommended EnvironmentOutdoor

Product Videos

Product Reviews

Product Questions & Answers

Top